UserManual:Detail

Detail Toolbox

Overview

This is where you add all those little touches that breathe life into your pattern. First, we will go over the tools in the Detail toolbox.

Tools

Workpiece Tool

The Workpiece tool, found on the top-left of the Details toolbox, (just under the pointer,) allows you to trace out your pattern by selecting nodes, (points & splines,) in a clockwise direction around its outline. This tool must be used before any of the other Detail magic can be accessed.

Internal Path

The Internal Path tool, found on the right-hand side of the toolbox, allows you to set things like pocket placement markings.

Pin Tool

The Pin tool, found on the left-hand side of the toolbox, allows you to set certain points for attaching features like grainlines & labels to.

Node Tool

The Insert Node tool, found on the lower right-hand side of the toolbox, allows you to add points & curves to your pattern piece which you missed when you traced it earlier. You will then find them, excluded, at the end of the list of nodes in the pattern piece options dialog in the pattern piece screen where you will need to shift them into their proper places & activate them.

Detail Mode

The detail mode, perhaps better called the pattern piece screen, is the second of the three steps to producing a pattern with Seamly2D.

Overview

So, you've traced out your pattern with the Workpiece Tool, & have likely been confused by how limited the Workpiece Tool dialog box was by the number of options greyed out. But now you've made it to the Detail screen & are wanting to know just what all you can do now. The pattern piece options dialog, (which you previously met as the Workpiece Tool dialog,) is now fully operational.

Pattern Piece Options Dialog (Workpiece Tool)

Right-click any of the pattern pieces visible on the Detail screen, & a menu will pop up . The top item is Options, which is what we will be discussing now. Go ahead & click on it.

Paths:

The Paths section has three tabs: Main path, Seam allowance, & Internal paths.

Main path

Forbid flipping defaults to off. Theoretically, checking it prevents your pattern pieces from being mirrored. In practice, I have been unable to establish any effect.

Hide main path defaults to off. If you turn both this & Seam allowances on, the "main path," (which in this case amounts to the stitch line,) will not be shown on your pattern piece.

Next, we have the adjustable list of nodes constituting the main path of your pattern piece in clockwise order. Node is a catch-all term for the points & curves which define the pattern area. If a node was added out of the correct order you can drag it to its rightful place in the clock; shifty arrow buttons are also available, which is super handy if you're using a track-pad. If you right-click a node, a menu will pop up. If the node is a point, it will ask if it should be marked as a Notch, be Excluded, or be Deleted. If the node is a curve, it will ask if it should be Reversed, be Excluded, or be Deleted. If your curve was made in a way which was counter-clockwise to the main path, it will need to be reversed.

To the left of the nodes is a column of icons denoting special features relating to said nodes. If the node is a curve, there will be a loopy-arrow icon. If the curve was made in a way which was clockwise with the main path, the arrow must loop in the default clockwise direction, if the curve was made in a way which was counter-clockwise to the main path, it will need to be reversed, which shows as a counter-clockwise arrow. If the node is a notch, the icon will show which shape of notch it is.

Seam allowance

Seam allowance defaults to off. Check the box to access the options.

Built in defaults to off. If your seam-allowance was included in your drafting system, check this box. Notches don't show-up without a seamline, so while you could get away without turning seam allowance on, if you want your notches marked, this is how to take care of that.

In the Automatic section:

Width defines the default width for seam allowances in this pattern piece. There is also a universal option for that in the Preferences. If you're using Inches, 0.625=(5/8) without any further input your seam allowance would be 5/8" all the way around. However, there's a decent chance that you'll make a pattern that gets placed on a fold, in which case you have to mess with Nodes.

Toolbox

Union Tool

On the top right of your Details Toolbox, you will see the Union tool. This tool allows two pattern pieces to become one, joined together along the line between two points on either separate piece. At this point in time the tool will not flip the pattern pieces, but it will rotate them as needed. If the line segments are different lengths, the piece with the smaller segment will be aligned with the other piece in relation to which piece you selected first. I haven't been able to figure out what the rule(s) is, if you don't like how it turned out one way, try it a different way until it looks right. One of the points will always overlap a point on the opposite piece, no centering.

Tools for creating details

On the bottom right of your details toolbox you will find the Tools for creating details tool. Hopefully I will remember to come back & update this after I have a chance & remember to poke at this tool with a stick.