UserManual:Detail: Difference between revisions
no edit summary
Pneumarian (talk | contribs) (→Seam allowance: Added the Internal Paths section.) |
Grace Kwatie (talk | contribs) No edit summary |
||
(5 intermediate revisions by one other user not shown) | |||
Line 4:
=== Overview ===
This is where you add all those little touches that breathe life into your pattern. First, we will go over the tools in the
=== Tools ===
====
The
==== [[UserManual:Detail#Internal Path|Internal Path]]====
The Internal Path tool, found on the right-hand side of the toolbox, allows you to set things like pocket placement markings and darts.
==== [[UserManual:Detail#Pin Tool|
The
====[[Node Tool]]====
The Insert Node tool, found on the lower right-hand side of the toolbox, allows you to add points & curves to your pattern piece which you missed when you traced it earlier. You will then find them, excluded, at the end of the list of nodes in the pattern piece
==
The
===Overview===
So, you've traced out your pattern with the Workpiece Tool, & have likely been confused by how limited the
=== Pattern Piece Options
Right-click any of the pattern pieces visible on the
==== Paths: ====
The Paths section has three tabs: Main path, Seam allowance,
===== Main path =====
''Forbid flipping'' defaults to off. Theoretically, checking it prevents your pattern pieces from being mirrored. In practice, I have been unable to establish any effect.
Line 39 ⟶ 40:
Next, we have the adjustable list of nodes constituting the main path of your pattern piece in clockwise order. '''''Node''' is a catch-all term for the points & curves which define the pattern area.'' If a node was added out of the correct order you can drag it to its rightful place in the clock; shifty arrow buttons are also available, which is super handy if you're using a track-pad. If you right-click a node, a menu will pop up. If the node is a point, it will ask if it should be marked as a ''Notch'', be ''Excluded'', or be ''Delete''d. If the node is a curve, it will ask if it should be ''Reverse''d, be ''Excluded'', or be ''Delete''d. If your curve was made in a way which was counter-clockwise to the main path, it will need to be reversed.▼
▲Next, we have the adjustable list of
To the left of the
===== Seam allowance =====
''Seam allowance'' defaults to off. Check the box to access the options.
''Built in'' defaults to off. If your seam-allowance was included in your drafting system, check this box. Notches don't show-up without a seamline, so while you could get away without turning seam allowance on, if you want your notches marked, this is how to take care of that.
In the '''Automatic''' section:
''Width'' defines the default width for seam allowances in this pattern piece. There is also a universal option for that in the Preferences. If you're using Inches, 0.625=(5/8) without any further input your seam allowance would be 5/8" all the way around. However, there's a
In a cruel twist of fate, "Nodes" in this situation applies only to points. There is a drop-down menu labeled "Node:" to choose which point you want to affect the seam allowance in relation to. Remember that your pattern is traced in a clockwise order. Next we come to two fields labeled "Before" & "After," pre-filled with "CurrentSeamAllowance" which means that the seam allowance on that side of the point will be the same as defined in Width above. You can change them to any ridiculous extreme you feel like, but 0 (zero/zed) for a foldline, or a suitable hemwidth for a hemline are probably the most common choices when "CurrentSeamAllowance" is not appropriate.
In the '''Custom''' section:
I have no idea if this even does anything. I appears completely null. (This section is there for future plans in the programming.)
===== Internal Paths =====
A lovely list of the internal paths this pattern piece has. If you right-click one of the paths a menu will pop up allowing you to either access the Internal Path Tool via the term "Options," or delete the path.
In the '''Internal Path Tool''' you have a few options:
You can change the path's ''name'', which defaults to "Unnamed path", to something more relevant, like "Pocket Placement" or "top-stitching" or "Bob."
Line 76 ⟶ 85:
Then we have a customizable list of nodes used to shape the internal path, with adjustment arrows below for those who find clicking easier than dragging.▼
▲Then we have a customizable list of nodes used to shape the internal path, with adjustment arrows below for those who find clicking easier than dragging.
==== Pins: ====
A list of the "Pins" this pattern piece has. Right-click for a menu to delete pins. Drag to sort.<br />
====
If someone else, (or you at a later date,) will need to know what a pattern piece you've drafted is all about, use a label!
===== Piece Label Data =====
The first tab of this section, Piece Label Data is where you tell Seamly what to display on the label.
===== Labels =====
The second tab of this section, Labels, is where you establish the size & placement of your labels.
==== Grainline: ====
In this section you establish whether to display the grainline, & place your grainline marks. In that sense it could almost be a tab in the Labels section.
==== Notches: ====
Which notch should be which shape, set in which way, & which size? & should it be single? paired? triple? Way cooler than the misnamed "passmark" of older versions of Seamly2D.<br />
===Toolbox===
==== [[UserManual:Detail#Union Tool|
<blockquote>'''This tool is currently being upgraded.'''</blockquote>On the top right of your Details Toolbox, you will see the
==== Tools for creating details: ====▼
On the bottom right of your details toolbox you will find the ''Export Pieces'' tool. Clicking this button will bring up a dialog labeled "Save Layout."
===== Save Layout dialog =====
The '''Path''' option defaults to the layout folder named in your preferences & allows you to change it.
The '''File format''', which defaults to .svg, is a drop-down which allows you to choose which format you want to save the layout as.
You can check the box for '''Binary form''' if you chose one of the .dxf options.
Those are also the most likely ones to need the '''Text as paths''' box checked.
This user is not sure what the point of the greyed-out '''Margins''' & '''Paper format''' are even doing here. It is likely that as of this posting those capabilities have not been implemented sufficiently.
The '''File name''' option defaults to <.val name>_1. It implies that the 1 is optional, but, at least in Linux, actually insists that all files end in a 1.
▲==== Tools for creating details ====
==Finishing Patterns in Detail Mode==
|