Sleeve Block, McCunn System: Difference between revisions
No edit summary |
No edit summary |
||
Line 32: | Line 32: | ||
The McCunn method uses two reference lines. The '''Sleeve Centerline''' is drawn as a vertical line with length equal to the Valentina measurement '''arm_shoulder_tip_to_wrist_bent'''. The '''Biceps Line''' is drawn at a right angle to the Sleeve Centerline with half of the length of the Valentina measurement '''arm_upper_circ''' plus wearing ease extending on each side from the center. This line is drawn at a distance of '''arm_shoulder_tip_to_armfold_line''' from the top of the Sleeve Centerline. The '''Wrist Line''' is drawn at a right angle to the Sleeve Centerline with half of the length of the Valentina measurement '''hand_palm_circ''' extending on each side from the center. This line is drawn at the wrist end of the Sleeve Centerline. |
The McCunn method uses two reference lines. The '''Sleeve Centerline''' is drawn as a vertical line with length equal to the Valentina measurement '''arm_shoulder_tip_to_wrist_bent'''. The '''Biceps Line''' is drawn at a right angle to the Sleeve Centerline with half of the length of the Valentina measurement '''arm_upper_circ''' plus wearing ease extending on each side from the center. This line is drawn at a distance of '''arm_shoulder_tip_to_armfold_line''' from the top of the Sleeve Centerline. The '''Wrist Line''' is drawn at a right angle to the Sleeve Centerline with half of the length of the Valentina measurement '''hand_palm_circ''' extending on each side from the center. This line is drawn at the wrist end of the Sleeve Centerline. |
||
'''PLEASE NOTE THAT THIS PAGE IN UNDER CONSTRUCTION. ''' |
|||
Palm |
Palm |
||
Shoulder to Elbow |
Shoulder to Elbow |
Revision as of 17:33, 29 May 2017
Sleeve Block, McCunn System
These instructions are based on the instructions and method from the book How to Make Sewing Patterns by Don McCunn (1977 revised edition) ISBN 0-932538-00-2. This book has been updated and may be purchased from Amazon: https://www.amazon.com/How-Make-Sewing-Patterns-second/dp/0932538215. In this tutorial, the method described there will be referred to as “the McCunn method”.
Measurements
The following Valentina measurements are required to construct a sleeve block using the McCunn method.
- L01 arm_shoulder_tip_to_wrist_bent
- L16 arm_shoulder_tip_to_armfold_line
- L11 arm_upper_circ
- D04 hand_palm_circ
- L02 arm_shoulder_tip_to_elbow_bent
Before attempting to draft a sleeve pattern with this method, ensure that you have created and saved a measurement file (.vit) which contains values for L01, L02, L11, L16, and D04. This may be accomplished using the TAPE program.
The instructions for drafting a basic sleeve may be found on pages 71-75 in the 1977 revised edition or pages 79-82 in the 2016 second edition. In the McCunn method, the five measurements required to draft a basic sleeve are called
- Arm Length
- Sleeve Cap
- Biceps
- Palm
- Shoulder to Elbow
Formulas
Figure 1 shows the basic reference lines and other major lines used in constructing the main portion of the sleeve.
![](http://static.miraheze.org/seamlywiki/thumb/5/5b/Mccunn-sleeve-construction.jpg/300px-Mccunn-sleeve-construction.jpg)
The McCunn method uses two reference lines. The Sleeve Centerline is drawn as a vertical line with length equal to the Valentina measurement arm_shoulder_tip_to_wrist_bent. The Biceps Line is drawn at a right angle to the Sleeve Centerline with half of the length of the Valentina measurement arm_upper_circ plus wearing ease extending on each side from the center. This line is drawn at a distance of arm_shoulder_tip_to_armfold_line from the top of the Sleeve Centerline. The Wrist Line is drawn at a right angle to the Sleeve Centerline with half of the length of the Valentina measurement hand_palm_circ extending on each side from the center. This line is drawn at the wrist end of the Sleeve Centerline.
PLEASE NOTE THAT THIS PAGE IN UNDER CONSTRUCTION. Palm Shoulder to Elbow
![](http://static.miraheze.org/seamlywiki/thumb/8/87/McCunn-sl-cap-const.jpg/300px-McCunn-sl-cap-const.jpg)
Figure 2 shows the special points used in constructing the sleeve cap portion of the sleeve.